<div class="entry-content">
    <div class="jetpack-video-wrapper"><span class="embed-youtube" style="text-align:center; display: block;"><iframe src="https://www.youtube.com/embed/Ifb6nKOu2Go" class="youtube-player" width="740" height="416.418" frameborder="0" allowfullscreen></iframe></span>
    </div>
    <div class="blog-content">
Ways to go around chip / software protection. Thank you very much Davide Toldo
    </div>
    
    <div class="blog-content-links">
        <div>
            Links:
        </div>
        <ul class="links-list">
            <li class="links-list-item"><a href="https://www.linkedin.com/in/davide-t-698320255/">Davide's Linkedin</a></li>
            <li class="links-list-item"><a href="https://fedevel.com/courses">FEDEVEL Online courses</a></li>
        </ul>
    </div>  
</div>

How to hack a chip? Watch this example

<div class="entry-content">
    <div class="jetpack-video-wrapper"><span class="embed-youtube" style="text-align:center; display: block;"><iframe src="https://www.youtube.com/embed/wG3utzF4Ch0" class="youtube-player" width="740" height="416.418" frameborder="0" allowfullscreen></iframe></span>
    </div>
    <div class="blog-content"> 
         Going through simple but useful electronic board tests. Thank you very much Waseem Alkhayer
    </div>

    <div class="blog-content-chapters">
        <div>
            Chapters:
        </div>
        <ul class="chapters-list">
            <li class="chapters-list-item"><span class="chapters-time">00:00</span><span class="chapters-text">What is this video about</span></li>
            <li class="chapters-list-item"><span class="chapters-time">05:01</span><span class="chapters-text">Why to test</span></li>
            <li class="chapters-list-item"><span class="chapters-time">10:59</span><span class="chapters-text">Test 1: Heat</span></li>
            <li class="chapters-list-item"><span class="chapters-time">19:57</span><span class="chapters-text">Test 2: Cold / Freezing</span></li>
            <li class="chapters-list-item"><span class="chapters-time">33:16</span><span class="chapters-text">IP67</span></li>
            <li class="chapters-list-item"><span class="chapters-time">33:58</span><span class="chapters-text">Test 3: Water</span></li>
            <li class="chapters-list-item"><span class="chapters-time">37:40</span><span class="chapters-text">Test 4: Dust</span></li>
            <li class="chapters-list-item"><span class="chapters-time">42:44</span><span class="chapters-text">Test 5: Humidity</span></li>
            <li class="chapters-list-item"><span class="chapters-time">48:55</span><span class="chapters-text">Test 6: Salt Water</span></li>
            <li class="chapters-list-item"><span class="chapters-time">53:47</span><span class="chapters-text">Test 7: Vibration</span></li>
            <li class="chapters-list-item"><span class="chapters-time">59:30</span><span class="chapters-text">Test 8: ESD</span></li>
            <li class="chapters-list-item"><span class="chapters-time">1:08:47</span><span class="chapters-text">Test 9: RF Immunity</span></li>
            <li class="chapters-list-item"><span class="chapters-time">1:12:15</span><span class="chapters-text">Summary</span></li>
            <li class="chapters-list-item"><span class="chapters-time">1:18:55</span><span class="chapters-text">About Waseem</span></li>
    </div>
    
    <div class="blog-content-links">
        <div>
            Links:
        </div>
        <ul class="links-list">
            <li class="links-list-item"><a href="https://www.linkedin.com/in/waseemalkhayer/">Waseem's Linkedin</a></li>
            <li class="links-list-item"><a href="https://fedevel.com/courses">FEDEVEL Online courses</a></li>
        </ul>
    </div>
</div>

9 Tricks To Test The Board You Designed - Do you use them?

<div class="entry-content">
    <div class="jetpack-video-wrapper"><span class="embed-youtube" style="text-align:center; display: block;"><iframe src="https://www.youtube.com/embed/VGY1qFE-kC0" class="youtube-player" width="740" height="416.418" frameborder="0" allowfullscreen></iframe></span>
    </div>
    <div class="blog-content">
I come up with this a long time ago and keep using it all the time.
    </div>
    
    <div class="blog-content-links">
        <div>
            Links:
        </div>
        <ul class="links-list">
            <li class="links-list-item"><a href="https://fedevel.com/courses">FEDEVEL Online courses</a></li>
        </ul>
    </div>  
</div>

Useful TIP: What Track Width To Use When Routing PCB?

<div class="entry-content">
    <div class="jetpack-video-wrapper"><span class="embed-youtube" style="text-align:center; display: block;"><iframe src="https://www.youtube.com/embed/zC5RxBF-Ydg" class="youtube-player" width="740" height="416.418" frameborder="0" allowfullscreen></iframe></span>
    </div>
    <div class="blog-content">
        This short video demonstrates how to use variant manager in Altium Designer. Once set up correctly it’s easy to generate BOMs or Print schematics for different variants.<br><br>

        What are different variants? For example in case you have some optional resistors which can be fitted for one variant, but not for other.
    </div>
</div>


Altium Designer Tutorial – Variants are useful

<div class="entry-content">

    <div class="blog-content">
        Here is the PCB stackup what I normally start with + requirements for minimum VIA, track, clearance and impedances.
        <ul class="content-list">
            <li class="content-list-item"><span class="content-text"><b>12 Layers:</b>
                <ul class="content-list">
                    <li class="content-list-item"><span class="content-text">L1 – Signal</span></li>
                    <li class="content-list-item"><span class="content-text">L2 – GND</span></li>
                    <li class="content-list-item"><span class="content-text">L3 – Signal</span></li>
                    <li class="content-list-item"><span class="content-text">L4 – Signal</span></li>
                    <li class="content-list-item"><span class="content-text">L5 – GND</span></li>
                    <li class="content-list-item"><span class="content-text">L6 – Powers</span></li>
                    <li class="content-list-item"><span class="content-text">L7 – Powers</span></li>
                    <li class="content-list-item"><span class="content-text">L8 – GND</span></li>
                    <li class="content-list-item"><span class="content-text">L9 – Signal</span></li>
                    <li class="content-list-item"><span class="content-text">L10 – Signal</span></li>
                    <li class="content-list-item"><span class="content-text">L11 – GND</span></li>
                    <li class="content-list-item"><span class="content-text">L12 – Signal</span></li>
                </ul>       
            </span></li>
            <li class="content-list-item"><span class="content-text"><b>Required impedances</b>
                <ul class="content-list">
                    <li class="content-list-item"><span class="content-text">Single ended: 50 OHMs (all signal layers)</span></li>
                    <li class="content-list-item"><span class="content-text">Differential: 70, 90 and 100 OHMs (all signal layers)</span></li>
                </ul>       
            </span></li>
            <li class="content-list-item"><span class="content-text"><b>Other requirements</b>
                <ul class="content-list">
                    <li class="content-list-item"><span class="content-text">Minimum through-hole VIA: 0.45mm (pad) / 0.2mm (drill)</span></li>
                    <li class="content-list-item"><span class="content-text">Minimum track / clearance: 0.1 mm / 0.1 mm (more expensive PCB: 0.075mm / 0.075mm)</span></li>
                </ul>       
            </span></li>
            <li class="content-list-item"><span class="content-text"><b>If uVIAs are used</b>
                <ul class="content-list">
                    <li class="content-list-item"><span class="content-text">uVIA: 0.25mm (pad) / 0.1mm (laser drilled hole)</span></li>
                    <li class="content-list-item"><span class="content-text">buried VIA: 0.45mm (pad) / 0.2mm (drill)</span></li>
                </ul>       
            </span></li>
        </ul>
     </div>

    <div class="blog-content-text">
        I also found useful information about HDI stackups in this Mentor document: <a href="http://www.mentor.com/pcb/resources/overview/hdi-layer-stackups-for-large-dense-pcbs-723df14d-88f7-4e34-b47f-178d8c69ba1b" >HDI Layer Stackups for Large Dense PCBs</a><br><br>

        HDI PCB technology comparison (picture from the Mentor document)
    </div>

    
    <div class="blog-content-img-wrapper">
        <img src="https://assets.fedevel.com/blog/2019/10/3ef7e-stackup_example.jpg" alt="stackup_example" />
    </div>

    <div class="blog-content-links">
        <div>
            Links:
        </div>
        <ul class="links-list">
            <li class="links-list-item"><a href="http://www.mentor.com/pcb/resources/overview/hdi-layer-stackups-for-large-dense-pcbs-723df14d-88f7-4e34-b47f-178d8c69ba1b" >HDI Layer Stackups for Large Dense PCBs</a></li>
        </ul>
    </div>  
</div>

PCB stackup example – minimum track, clearance, VIA …

<div class="entry-content">
    <div class="jetpack-video-wrapper"><span class="embed-youtube" style="text-align:center; display: block;"><iframe src="https://www.youtube.com/embed/6AU94oTnG68" class="youtube-player" width="740" height="416.418" frameborder="0" allowfullscreen></iframe></span>
    </div>
    <div class="blog-content">
        This short video demonstrates how to create a simple 3d component in Altium Designer.
    </div>
    <div class="blog-content-links">
        <div>
            Links:
        </div>
        <ul class="links-list">
            <li class="links-list-item"><a href="http://www.fedevel.com/welldoneblog/2011/08/altium-designer-3d-model-of-your-pcb-its-reallyeasy/">Altium Designer – 3D model of your PCB – it’s really easy</a></li>
        </ul>
    </div>  
</div>


| KNOWLEDGE BASE

A rich source of expert knowledge

Altium Designer Tutorial – Create 3D component / footprint

Newest Posts

How to hack a chip? Watch this example

9 Tricks To Test The Board You Designed - Do you use them?

Useful TIP: What Track Width To Use When Routing PCB?

Categories

BUSINESS ADDRESS